IT IS IMPORTANT
- Check all product/wires/accessories for damage from time to time. A damaged or non-functional part must not be used any longer. If the product, accessories or cords are damaged, contact an Oral-B service center. Do not repair or modify the product yourself. Doing so may cause fire, electric shock, or other damage.
- Not recommended for use by children under 3 years of age. Children and persons with reduced physical, sensory or mental capabilities or lack of experience can use the device after they have been taught how to use it safely and have been advised of the hazards.
- Cleaning and servicing of the product should not be performed by children.
- Do not allow children to play with the device.
- Use the product only for its intended purpose as described in this manual.
- Do not use accessories not recommended by the manufacturer.
CAREFULLY
- If the device is dropped, the attachment must be replaced before next use, even if there is no visible damage.
- Do not expose the charger, plug, or travel case to water or other liquids, or place them where they could accidentally fall into a sink or bathtub. If these devices fall into water, do not remove them. Unplug them immediately.
- Do not open or disassemble the device. To recycle the battery, please dispose of the entire device in accordance with the environmental regulations applicable in your area. Damage to the handle will damage the device and void the warranty.
- When unplugging the device, hold it by the plug, not the cord. Do not touch the plug with wet hands, as this may cause electric shock.
- If you are being treated for an oral condition, consult your healthcare professional before using the device.
- This toothbrush is intended for individual use and cannot be used by multiple patients in a dental clinic or institute.
- Replace the brush (head) every three months, or more often if it is very worn.
- The travel case with charging function is equipped with a special power cord (smart plug) for connecting to the network, equipped with a built-in safety extra-low voltage power supply. Do not replace or disassemble its components, as this may cause electric shock. Use only the power cord that came with your device.
Important information
- Your Oral-B toothbrush can connect to your smartphone (see Connecting your toothbrush to your smartphone for more information).
- To avoid radio interference and/or compatibility issues, turn off the radio transmitter on the brush handle (5) before using it in restricted areas such as airplanes or designated areas in hospitals.
- To turn off the radio transmitter, simultaneously press and hold the on/off button (3) and the mode button (4) for two seconds until the radio transmission display (7) goes out. Follow the same steps to turn the transmission back on.
- If you use a pacemaker, do not bring the brush closer than 15 centimeters to it while it is on. If you experience interference, immediately turn off the radio transmitter in the handle.
What is the procedure for changing heads on electric toothbrushes from different brands?
The situation is that the design and operating principle of different electric toothbrushes are the same: the lower element is responsible for the mechanism that ensures vibration and operation of the entire toothbrush, and the upper element is equipped with a replaceable brush head . Therefore, we will always have a nozzle , so the answer to the question “how to replace the nozzle on an electric toothbrush” is the same for different manufacturers - we remove the nozzle from above and put a new one in its place.
To summarize, it doesn’t matter which electric toothbrush you have - Oral-B or Philips Sonicare, the principle of replacing brush heads does not change. a nozzle is placed on top of the toothbrush , and to replace it you will need to gently pull out the old nozzle to put on the new one.
READ Brushcutter Attachment for Snow Clearing
Charging and use
Your toothbrush has a waterproof handle and is designed for safe use in the bathroom.
- You can start using the toothbrush immediately or after a short charging period by placing it on the charging station (9). Note: if the battery is completely discharged (the charge level indicator light on the display (8) does not light up during charging, or the device does not respond to pressing the on/off button (3)), it is necessary to charge it for at least 30 minutes.
- The charge level is displayed on the charge indicator (8). A flashing light means the brush is charging (Fig.①); Once charging is complete, the indicator light turns off. A full charge usually takes 15 hours and lasts for up to 12 days of regular toothbrush use (twice a day for two minutes) (Fig.①).
- Note: If the device is completely discharged, the indicator light may not light up for the first 30 minutes of charging.
- When the battery charge is low, the red indicator light on the charge level display starts flashing and the motor speed decreases. When completely discharged, the motor will stop; For single use, you will need to charge the device for at least 30 minutes.
- You can keep the handle on the plugged-in charger at all times to maintain a full charge; The device is protected from overcharging. Note: For best performance, store the brush handle at room temperature.
Caution : Do not expose the handle to high temperatures above 50°C.
Using your toothbrush
Teeth brushing technique
Wet the brush head and apply any toothpaste. To prevent splashing, bring the brush head close to your teeth before pressing the button on the handle (Fig.②). If you are using one of the Oral-B rotating brush heads, move it slowly from tooth to tooth, pausing on each surface for a few seconds. When using the Oral-B TriZone , place the bristles of the brush against your teeth at a slight angle to the gum line. Apply gentle pressure and begin brushing in a back-and-forth motion, similar to a manual toothbrush. Regardless of the brush head you use, start on the outside of your teeth, move to the inside, and then clean the chewing surfaces. Give equal attention to all four quadrants of the mouth.
You can also consult your dentist or oral hygienist about the technique that is best for you.
During the first few days of using any electric toothbrush, your gums may bleed a little. Usually this phenomenon stops after a few days. If bleeding gums persist for two weeks, contact your dentist or oral hygienist. If you have sensitive teeth and/or gums, Oral-B recommends using the Sensitive mode (possibly in combination with the Oral-B Sensitive brush head).
Smart Ring
Your toothbrush is equipped with Smart Ring technology, which varies depending on the color of the light: White (default) = activity indicator and visual timer (select a different color in the Oral-B™ app settings)
red = pressure sensor indicator
blue = Bluetooth® connection indicator
Timer
You can choose "Professional" or "Two Minute" mode
The “Two Minute” timer turns on a long intermittent beep and a flashing Smart Ring light (2) when two minutes have elapsed—the length of time recommended by experts for brushing your teeth.
The “Professional” timer gives a signal to move to the next quadrant of the oral cavity with a short intermittent sound signal and a flashing Smart Ring light indicator (2) (Fig. ③). A long intermittent beep and a flashing light indicate the end of the two-minute period of brushing your teeth in accordance with the recommendations of specialists.
The timer remembers the elapsed time even if the brush is turned off briefly during use. The timer is reset when there is a pause longer than 30 seconds, a short press on the mode selection button (4) during the pause, or placing the brush handle on the charger.
Note: When using special options in the Oral-B™ app, the visual timer may be deactivated.
Timer setting:
By default, your brush has the Professional timer activated. To change settings, press and hold the mode button (4) for 2 seconds. Select the timer mode with the “on/off” button (3). Confirm your choice by pressing the mode button.
- 2 light signals - “Two-minute” mode is selected
- 4 light signals - “Professional” mode is selected
Note: You can also set/adjust the timer through the Oral-B™ app.
Pressure meter
If you press too hard on the brush, the Smart Ring (2) lights up red, indicating the need to release the pressure. In addition, the head will stop pulsating and its rotation speed will decrease (in “Daily”, “Professional” and “Sensitive” modes) (Fig.③). Periodically check the operation of the pressure sensor by applying gentle pressure to the brush during use.
Operating modes (depending on model)
Your toothbrush offers different brushing modes. The selected mode is reflected in the mode display (6) on the brush handle (except for the “Daily Cleaning” mode):
“ Daily brushing ” is a standard regimen for daily oral care
“ Professional cleaning ” – for a feeling of unusual cleanliness (high frequency of movements)
“ Gentle Cleaning ” – gentle but thorough cleaning of sensitive areas
“ 3D White ” – polish for periodic or daily use
“ Gum care ” – gentle gum massage
“ Tongue hygiene ” – cleaning the tongue for periodic or daily use
To use the Tongue Hygiene mode, we recommend using the Sensitive attachment. You can clean your tongue with or without toothpaste. Brush the entire surface of the tongue with gentle, systematic movements. The recommended time is 20 seconds, its end is indicated by a flashing Smart Ring light signal.
Your toothbrush automatically starts in the last mode you selected. To switch to another mode, press the mode button successively while using the brush (Fig.④). To return to the “Daily Cleaning” mode from any other mode, press and hold the mode selection button (4).
Note: You can also select/adjust the mode through the Oral-B™ app.
Oral B
This company produces electric toothbrushes and brush heads in other countries under the excellent name Braun. Therefore, if you use an Oral B toothbrush and, when choosing attachments, you notice the Braun company, you don’t have to think about their compatibility. In total, the company produces 7 types of nozzles:
- SENSETIVE
. This type is designed for people with increased sensitivity (by the way, here are effective ways to dull painful sensations). The characteristics of the nozzle include soft, thin bristles. Suitable for daily oral hygiene, but we recommend alternating its use with medium-hard bristles. It removes plaque better. - 3D-WHITE
. Designed for whitening. The design of the nozzle implies the presence of a rubber rod for polishing tooth enamel. Around this rod there are medium-hard bristles. By the way, here are interesting methods for home teeth whitening. - CROSS-ACTION, PRECISION-CLEAN
. Attachments aimed at daily oral hygiene. They have medium hard bristles. They differ in the arrangement of the bristles: for Cross-Action it is cross, for Procession-Clean it is straight. - FLOSS-ACTION
. The medium-hard bristles are supplemented with rubber bristles for better cleaning of the spaces between the elements of the dentition. This is a great option for those who don't have time to floss. - SENSI-ULTRA
. The design combines both medium-hard and soft bristles. The harder bristles are located in the center of the nozzle, the soft bristles are located in a circle. This is also an electric brush head designed for sensitive teeth and gums. - TRIZONE
. Unlike its round counterparts from Oral B, it has an oval shape with differently located bristles that move in different directions. An interesting attachment that has earned particular popularity among consumers. - Baby attachments
. All existing attachments for children differ only in color. Made from soft bristles.
Oral B attachments are considered more effective for daily cleaning of the oral cavity.
We have already written about how to properly brush your teeth with an electric brush here.
Replaceable attachments
Oral-B offers you a variety of replacement attachments to fit your Oral-B handle.
Our rotating brush heads are used to precisely clean every tooth.
Oral-B CrossAction attachment
The most advanced of our attachments. Angled bristles for precise cleaning. Removes and eliminates plaque.
Oral-B FlossAction Attachment
Micropulsating bristles allow for effective plaque removal in the space between teeth
Oral-B 3D White
Special polishing cap for natural teeth whitening. Not suitable for use by children under 12 years of age.
Oral-B Sensi Ultrathin nozzle
It is a combination of regular bristles for cleaning the surface of teeth and ultra-fine bristles for cleaning areas along the gum line.
Most Oral-B brush heads are equipped with light blue INDICATOR® bristles, allowing you to keep track of when the brush head needs to be replaced. If you brush your teeth thoroughly twice a day for two minutes, the bristles will fade by half in about three months, demonstrating the need to change the brush head. If the bristles become frayed before the color has faded, you may be pressing too hard on the brush when brushing.
We do not recommend using Oral-B FlossAction or Oral-B 3D White attachments if you wear braces.
The Oral-B “Ortho” brush head is specially designed for cleaning teeth around braces and braces.
How often do you need to change attachments?
It is recommended to change heads for electronic brushes as often as regular toothbrushes, that is, once every 2-3 months. The reason for such frequent replacement is the accumulation of bacteria and wear of the nozzle itself. Even with the most careful use and careful storage of the device, the minimum period of 2-3 months remains. If you are not so careful about hygiene products, it is recommended to change the nozzles even more often.
The easiest way to determine whether a device is unsuitable for use is by its appearance, for example, if the bristles are frayed. Each family member should have an individual nozzle. They should be stored separately, so that the brushes do not touch. If you develop pathologies in the oral cavity, change the nozzle immediately. After recovery, it is advisable to change the device again. Careful storage and attentiveness of the user will not only increase the life of the nozzle, but also maintain health.
We recommend consulting with your dentist when choosing an electric toothbrush head. Only a doctor can tell whether the device will harm you and whether it can be used for your oral condition.
Tags: toothbrush, toothbrush heads, list, electric brush
About the author: DrZubastik
- Related Posts
- How to choose the right irrigator: advice from a dentist
- How to brush teeth with braces: instructions with pictures
- Everything about caring for children's teeth
« Previous entry
Connecting a toothbrush to a smartphone
The Oral-B™ app is available for mobile devices running iOS or Android operating systems. It can be downloaded from App Store(SM) or Google Play™.
A sensor is built into the handle of the toothbrush, which, through a mobile application, determines the location of the toothbrush and helps brush your teeth. Use a smartphone holder (for more details, see the “Accessories – Smartphone Holder” section).
What's more, the Oral-B™ app allows you to track your brushing progress and create custom brush settings (see Oral-B™ app instructions for other benefits).
- Launch the Oral-B™ app. It will help you set up a Bluetooth connection.
- Note: The functionality of the Oral-B™ app is limited if your smartphone's Bluetooth wireless technology is disabled (refer to your smartphone's manual for connection instructions).
- All instructions for using the application will be displayed on your smartphone.
- If Bluetooth wireless technology is activated on the brush handle, the Bluetooth symbol on the radio transmission display (7) will light up. Once the connection is established, the Smart Ring (2) will blink once.
- When using the brush, keep your smartphone nearby (up to 5 m). Make sure it is placed securely in a dry place.
Note: To connect to your toothbrush, your smartphone must have Bluetooth 4.0 (or higher)/Bluetooth Smart.
A list of compatible smartphones is available in the App Store(SM) or Google Play™.
Caution: Refer to your smartphone's user manual for information regarding whether the device/charger can be used in the bathroom.
For country availability of the Oral-B™ app, see www.oralbappavailability.co.uk.
Replacing the head on an electric toothbrush
In this post, we will take a closer look at how to replace the brush head on an electric toothbrush. This is done quite simply and quickly.
Using an electric toothbrush requires periodically replacing the brush heads with new ones. As we already know, replacement nozzles need to be changed at least once every three months. But if you have just recently switched from a regular toothbrush to an electric one, the question may arise - how to do this correctly? The mechanism for replacing nozzles is quite simple, takes little time and requires minimal effort. Even a child can change the brush head on an electric toothbrush!
When we buy an electric toothbrush, we receive instructions on how to use it. But the situation is completely different with toothbrush heads: rarely does any manufacturer write detailed instructions on how to replace the head with a new one. It is not a problem to replace the nozzle if you have already done a similar procedure before. Or at least seen other people doing it.
But what should you do if you are going to replace the head on your electric toothbrush for the first time?
Accessories
(Depending on model)
Smartphone holder
- Before each use, make sure that the mirror to which the holder will be attached, the suction cups (11d) and the holder brackets (11a) are clean and dry (Fig. B1). Use a smooth cloth to clean the surface of the suction cups and mirror. Make sure the surface of the suction cups and mirror is clean (no dust, hair, oil, lint, dirt, etc.).
- Gently press the smartphone holder (11) with sufficient force, attaching it approximately at nose level to the mirror. Then install the holder by pressing the lever (11b) until it clicks into place (Figure B2). Note: For proper and safe use, do not attach the holder to surfaces other than a mirror. For bathroom use only. Do not use in a car.
- Make sure the holder is securely attached to the mirror before placing your smartphone on it. Place the smartphone in a vertical position between the holder brackets (11a), pressing alternately on one of the brackets and pushing the second one to the side (Fig. B2). To remove the smartphone, repeat the procedure.
- Place the smartphone at the desired angle by turning the ball joint of the holder (Fig. B3).
- After brushing your teeth, remove your smartphone from the holder. To remove the holder, release the lever and carefully pull the tab (Fig. B4 1./2). Re-attach the holder to the mirror each time you use it.
- The smartphone holder can only be cleaned with a damp cloth (Fig.⑤). You can use glass cleaner, alcohol or similar products (avoid products with silicone oil). Make sure the surface is dry and clean. Store the holder in a clean and dry place. Do not leave your smartphone in the holder after use.
Note: Required smartphone width: no less than 58 mm, no more than 83 mm.
Caution : Small parts may break off, keep away from children.
Refer to your smartphone's manual for information on whether the device/charger can be used in the bathroom.
Travel charging module
- To charge the toothbrush handle (5), place it on the lip of the travel charger (12) and connect it to power using the optional power cord (13).
- The flashing indicator light (12a) of the travel charging module indicates that charging is in progress. When fully charged, the indicator turns off. A full charge takes up to 12 hours (Figure C1). Note: When the travel charger is plugged in, you can use the USB port (12b) to charge any other electronic device. The toothbrush can only be charged via the power cord (13)/(12c), but not via the USB port.
- The internal lighting unit of the travel charging module has a built-in holder (12d) on which you can place your smartphone while using the brush (Fig. C2). Before use, make sure that the smartphone fits the dimensions of the stand and is securely fastened.
- The removable inner layer (fig. C3) (12e) of the travel charging module can be washed in the dishwasher (fig. ⑤). The external module is cleaned with a damp cloth. Make sure the parts are completely dry before assembly and that the toothbrush/head is dry before placing it in the module.
Note: Remove stains from the surface of the module immediately. Store the module in a clean and dry place.
Refer to your smartphone's user manual for information on whether the device/charger can be used in the bathroom.
Cosmetic bag
Keep the toothbrush clean and dry in the travel case (15) in the cosmetic bag (14) (Fig. D1/2). Immediately remove stains from the surface of the brush. The cosmetic bag can only be washed by hand in warm water (30°C-40°C) (Fig. ⑤). Store in a dry, clean place.
Warranty
We [Braun] provide a two-year warranty on the product from the date of purchase.
During the warranty period, we [Braun] agree to correct, free of charge, any product defects resulting from defects in materials or workmanship by repairing or replacing the product at our option.
This warranty applies to all countries in which the device is supplied by Braun or its designated distributor. The warranty does not cover damage resulting from misuse or normal wear and tear of the product, especially with regard to attachments, or defects that have a minor effect on the operation of the device.
The product will be voided if repairs are carried out by unauthorized persons or if non-original Braun spare parts are used.
The device is equipped with an approved Bluetooth Smart radio module. Failure to establish a Bluetooth Smart connection with certain smartphone models is not covered by the warranty unless the device's Bluetooth radio module is damaged.
The warranty for Bluetooth devices is provided by the manufacturers of such devices and not by Oral-B. Oral-B does not have any influence or recommendation on the manufacturers of such devices and therefore is not responsible for the number of devices that are compatible with our Bluetooth systems.
Oral-B reserves the right, without prior notice, to make any technological modifications or changes in the system implementation of individual device elements, its interface or menu structure that it deems necessary for the proper functioning of these systems.
To carry out warranty service, hand over or send the device, complete and with a sales receipt, to an authorized Oral-B Braun Consumer Service Center.
Information
Bluetooth® radio module
Although Oral-B supports all designated Bluetooth device functions, we cannot guarantee 100% reliability of the connection and operation of the radio.
The performance and reliability of the connection directly depend on the characteristics of each specific Bluetooth device, the software version, the operating system installed on the Bluetooth device and the safety standards established by the manufacturer. Oral-B strictly adheres to the Bluetooth standard, which allows Bluetooth devices to connect and operate in conjunction with Oral-B toothbrushes.
However, if the device manufacturer does not comply with this standard, it may affect the compatibility and operation of Bluetooth devices and cause difficulties for the user. Please note that the software installed on your Bluetooth device may significantly affect connectivity and performance.
1) Warranty - exclusions and limitations
The limited warranty applies only to new products manufactured by or for The Procter & Gamble Company (“P&G”), its affiliates and subsidiaries and bearing the Braun/Oral-B brand, trademark or logo. The Limited Warranty does not apply to non-P&G products, including hardware and software. P&G is not responsible for damage to or loss of programs, data or other information stored on any media embedded in the product or for any product or part not manufactured by or for P&G and not covered by the limited warranty.
This limited warranty does not cover (i) damage caused by accident, abuse, careless or improper use or application, or damage to products not manufactured by or for P&G; (ii) damage caused by service performed by persons other than Braun and Braun-authorized service centers; (iii) products and parts modified without the written permission of P&G and (iv) damage caused by the use or inability to use the Oral-B Smartphone Stand, Smartphone Holder or Travel Case (“Accessories”),
2) Using a smartphone holder
The included Oral-B accessories allow you to conveniently position your smartphone while using the Oral-B app. Before using it for the first time, try out different positions of your smartphone in the Oral-B holder and choose the best one. Make sure that the smartphone will not fall or break. Do not use the accessory in a car.
LIMITATION OF LIABILITY
TO THE EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL P&G, ITS DISTRIBUTORS OR SUPPLIERS BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY KIND, DIRECT, INDIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, PUNITIVE DAMAGES OF ANY NATURE ARISING OUT OF USE OR INABILITY USE OF ORAL-B ACCESSORIES, INCLUDING WITHOUT LIMITATION, INJURY TO PERSON, DAMAGE TO PROPERTY, DEPRESSION OF THIRD PARTY PRODUCTS USED IN OR IN COMBINATION WITH ORAL-B ACCESSORIES, LOSS OF PERFORMANCE ORAL-B ACCESSORIES OR THIRD PARTY PRODUCTS USED IN OR IN CONJUNCTION WITH ORAL-B ACCESSORIES, INCLUDING P&G NOTIFYING THE POSSIBILITY OF SUCH AN OUTCOME. WITHOUT LIMITATION TO THE FOREGOING, YOU UNDERSTAND AND ACKNOWLEDGE THAT P&G SHALL NOT HAVE ANY RESPONSIBILITY FOR DAMAGE OR DESTRUCTION TO ANY CONSUMER ELECTRONIC DEVICES OR THIRD PARTY PROPERTY CONTAINED IN OR USED IN CONNECTION WITH ORAL ACCESSORIES. B, AS WELL AS FOR LOSS OF DATA CONTAINED IN THE MENTIONED DEVICES . IN NO EVENT SHALL ORAL-B'S REFUND EXCEED THE ACTUAL PRICE PAID FOR THE PRODUCT UPON PURCHASE.
Warranty for replacement tips
The device will be voided from Oral-B's warranty if damage to the device's electric rechargeable handle occurs as a result of using replacement attachments from another manufacturer.
- Oral-B does not recommend the use of refills from other manufacturers.
- Oral-B cannot control the quality of these brush heads and therefore cannot guarantee the quality of teeth cleaning they will provide, as stated upon initial purchase of the electric rechargeable handpiece.
- Oral-B cannot guarantee the compatibility of the Oral-B Handle with refills from other manufacturers.
- Oral-B cannot predict the long-term impact of using other brands of refills on handle wear.
All Orai-B refills have the appropriate logo and meet Oral-B's high quality standards. Oral-B does not sell refills or handpiece replacement parts under other brand names.
Oral-B electric toothbrush attachments
0 As sending failed Cancel as unsuccessful
0 Dislikes Fail Cancel Disliked
Thank you! We want to know why you liked this article
Thank you! We want to know why you didn't like this article.
All Oral-B electric toothbrushes remove plaque more effectively and gently than manual toothbrushes. But why then is there such a large selection of attachments, and how not to make a mistake in choosing?
First of all, it is worth saying that it is impossible to make a mistake. Currently, only Oral-B heads with reciprocating technology are officially sold in our region, which are suitable for all Oral-B electric toothbrushes (and even Oral-B battery-powered toothbrushes). So, no matter what Oral-B toothbrush heads you buy, they will fit. But the attachments differ in impact and effect. Choose carefully, focusing on the result you need now. CrossAction - modern Oral-B attachments. Each Oral-B attachment is created with the participation of dentists, following the example of professional dental instruments; the CrossAction attachment is the most versatile and progressive option. The Cross Action head design allows the bristles to wrap around each tooth on all sides, covering more surface area than a regular toothbrush. The 16° angled bristles not only provide excellent oral cleansing, but also significantly improve gum health. Thus, the Oral-B electric brush with 3D cleaning technology and the Oral-B CrossAction nozzle significantly reduces gingivitis in just 4 weeks. The different lengths of the bristles and the round shape of the head allow you to reach hard-to-reach areas and remove more plaque, which often remains when using a manual brush. The 3D White head has a specially designed teeth polishing bowl to remove stains from enamel, as well as classic, medium-hard bristles to remove plaque. Its rounded tips are absolutely safe for gums. An Oral-B toothbrush with this brush head perfectly cleans your teeth and helps you achieve a dazzling smile. The result is noticeable after 1-2 weeks of use. In addition, when the blue bristles of the Indicator discolor by half, this is a signal that the bristles are worn out, which means it’s time to replace the brush head. This brush head has soft bristles (all Oral-B brush heads except the Sensitive and Children's brush heads have medium-hard bristles). The soft bristles are suitable for cleaning sensitive and inflamed areas of the mouth or for dental care during the post-operative period (after consultation with the surgeon).
The Sensitive replaceable brush head cleans teeth more thoroughly than a regular toothbrush, while being as gentle as possible on oral tissue. With this attachment, you don't have to worry about your gums feeling uncomfortable.
The Floss Action head is suitable for electric toothbrushes and features yellow MicroPulse bristles that penetrate between teeth for excellent plaque removal. Brushing your teeth with this attachment does not replace flossing, but it gives a positive result and cleans the oral cavity better than a regular toothbrush. Feel comfortable and fresh in your mouth after brushing with an Oral-B toothbrush with a Floss Action attachment and forget about flossing for a long time. This head provides a deep clean using three-zone cleaning technology. The small bristles move from side to side, allowing you to brush your teeth just like a manual toothbrush, but with all the benefits of an electric one.
Trouble-shooting
Problem | Possible reason | Remedy |
The brush does not work (does not work properly) with the Oral-B™ app |
|
|
Resetting settings to factory defaults | Requires original mobile app functionality | Press and hold the on/off button (3) for 10 seconds until all indicator lights turn on twice simultaneously. |
The brush does not work (on first use) | Low battery level; no light indication. | Charge for at least half an hour. |
The brush does not work with SmartGuide. |
|
|
|
|
|
The brush does not dress up |
| The charge indicator may not start flashing immediately, but may take up to 30 minutes. The recommended ambient temperature for charging the battery is from 5 °C to 35 °C. |
This electric toothbrush is equipped with a Bluetooth radio module operating in the 2.4-2.48 GHz range with a maximum power of 1 mW.
Braun GmbH therefore declares that radio equipment types 3765, 3754, 3764,3762 and 3767 comply with the requirements of EU Directive 2014/53/EU. The full text of the European Declaration of Conformity is available for review on the following Internet page: https://www.oralb.com/ce
Made in Germany
Production date code:
To determine the year and month of manufacture, look at the manufacture code located on the charger or handle plate. Find a code (minimum 11 characters) starting with a letter.
Charger: The first digit of the code indicates the year of manufacture. The next two digits indicate the calendar week of the year of production.
For example: "509" means that the product was produced in the 9th week of 2015. Handle: The first digit of the production code indicates the year of production. The next two digits indicate the month of production.
For example: "509" means that the product was produced in September 2015.
Manufactured in Germany for Braun GmbH, Frankfurter Strasse 145, 61476 Kronberg, Germany/Braun GmbH, Frankfurter Strasse 145, 61476 Kronberg, Germany
RU Importer/Consumer Service: Procter and Gamble Distribution Company LLC, Russia, 125171, Moscow, Leningradskoe Shosse, 16A, building 2. Tel. 8-800-200-20-20
BY Suppliers to the Republic of Belarus: LLC "Electroservice and Co", Belarus, 220012, Minsk, st. Chernyshevsky, 10A, room 412AZ., IOO "ALIDI-West", 220140, Belarus, Minsk, st. Dombrovskaya, 9, of. 7.3.1. Service, Belarus, 220012, Minsk, st. Chernyshevsky, 10A, room 115 B
Warranty period/Service life: 2 years.
E.A.C.
Electric toothbrush type 3765 with charger type 3757, with portable charger type 3760 and mains adapter type 492-5214
220-240 Volts, 50-60 Hertz, 0.9 Watt
Electric shock protection class: II
What do you need to know about changing brush heads on an electric toothbrush?
We have already mentioned the frequency of replacing nozzles. What other considerations or precautions are there when replacing the brush head on an electric toothbrush?
As with any hygiene products, it is worth paying attention to a number of general rules. They are more concerned with personal hygiene and careful attitude towards replacing the element itself - the replaceable nozzle:
- Before replacing, wash your hands with soap and water.
- Be careful when opening the pack of attachments to avoid accidentally dropping them on the floor.
- Remove the old nozzle and install a new one in its place.
These rules are quite simple, but they should not be neglected. One of the most important rules, which essentially does not apply to the process of replacing the nozzle itself: before you start replacing the nozzle, be sure to wash your hands with soap. This necessary measure will prevent various harmful microbes from entering the body.